Trusted Attic Insulation for Henderson Homeowners
If your upstairs bedrooms hit 88°F by mid-afternoon while the thermostat reads 74, the insulation in your attic is the likely culprit. Henderson’s desert climate punishes a weak thermal envelope: summer attic temperatures routinely climb past 150°F, and a thin or settled layer of insulation lets that heat push straight down into your living space. Our technicians have up to 24 years of experience diagnosing exactly this problem, and we install and service attic insulation and spray foam only, nothing else. Requests placed before noon are often handled the same day, and every job comes with a written price before any work begins. Call (833) 734-5217 and a live person will answer, day or night.
Blown In Insulation
Blown In Insulation is loose fiberglass or cellulose that we machine-feed and blow across your attic floor to a measured depth, filling gaps and settling into the odd corners where batts don’t fit. You need it when your existing layer has compressed below the R-value your Henderson home was built to, which is common in older single-story tracts where original insulation has settled for years. We work with Owens Corning and GreenFiber among the eight brands we install, matching the material to your attic’s ventilation and your budget. Most attic jobs run between $1,500 and $3,500 depending on square footage and target R-value, and you’ll get the exact written number before we start. It’s the fastest, least disruptive way to cut cooling costs in a desert home.
How Blown-In Material Settles
Loose fill settles 10 to 20 percent in the first two years, which is why we install to a slightly higher depth than the label target. That margin keeps your attic at the R-value you paid for after settling. It’s also why a top-up on an older home often costs less than a full re-blow.
Attics With Tight Access
Low-pitch roofs and cramped scuttles make batt installation miserable and slow. Blown-in goes where a person can’t comfortably reach, covering all the framing, plumbing penetrations, and recessed can fixtures in one pass. We bag the material from outside or at the hatch, so your hallways stay clear.
Insulation Contractors
Insulation Contractors are the crews who measure your attic, recommend a material, install it, and stand behind the work, and choosing carefully matters more than most homeowners expect. You need a contractor when you’re buying a home and want the attic checked before closing, when a room-over-garage stays hot no matter what you do, or when a previous install is failing. We’re part of the Kingswell family of independently owned and operated insulation companies, and our attic and spray foam work is covered by the 365-Day Done Right Promise: if it’s not right within a year, we come back and fix it at no charge, in writing. Written pricing on a typical Henderson project lands between $1,500 and $3,500 for blown-in and $2,800 to $5,500 for spray foam, delivered before any work starts. Background-checked, uniformed technicians arrive in a committed window, and you know exactly who is walking into your home.
What a Written Price Includes
Our written price spells out the material, the R-value target, the square footage covered, and the disposal of old material if there is any. No door-step changes, no “while we were up there” upsells. What you see on paper is what you pay.
Reading a Contractor’s Estimate
An estimate that lists only a total is a red flag. Ask for the R-value, the brand of material, and whether removal of the existing insulation is included. A good proposal answers those three questions without a follow-up call.
Attic Ventilation
Attic Ventilation is the balance of intake and exhaust that lets trapped heat and moisture escape instead of baking your insulation from above. You need it checked when your attic smells musty, when the roof deck has dark staining, or when you’ve recently air-sealed and added insulation without adjusting airflow. In Henderson, a sealed attic with no working vents can reach 160°F on a July afternoon, and that heat shortens the life of shingles and drives your AC harder. We assess intake soffit vents against exhaust ridge or static vents and correct the imbalance, typically as part of a larger insulation job. Vent correction generally adds $400 to $1,200 depending on how many vents are added or unblocked, quoted in writing up front.
Balancing Intake and Exhaust
Most hot attics don’t have too little exhaust, they have clogged or missing intake. Soffit vents buried under insulation can’t pull air. We clear and baffle them so the system moves air the way it was designed to.
Ventilation and Moisture
Henderson runs dry most of the year, but winter cooking and laundry still push moisture up into the attic. Without ventilation that moisture condenses on cold surfaces and sets up mold. We test airflow while we’re up there, not after.
Radiant Barrier
Radiant Barrier is a reflective foil surface that we install facing down toward the attic floor to bounce radiant heat back before it can soak into the insulation below. You need it in Henderson when your attic hits its summertime peak and your ceiling still feels warm to the touch hours after sunset, which means radiant heat is doing the damage. We prefer to install it in combination with insulation rather than as a standalone fix, because a radiant barrier alone won’t stop the conductive heat gain that thin insulation allows. Most Henderson attic radiant barrier installs land between $1,000 and $2,400 for a typical single-family home, priced in writing before we touch a thing. Materials come from brands like CertainTeed and reflect the same way regardless of which side of the valley you live on.
Radiant Barrier and Existing Insulation
Radiant barrier works best over an insulated attic floor, not stapled to rafters in a ventilated attic. Placement matters as much as the foil itself. We show you the plan before we install.
When It’s Not Worth It
If your attic insulation is already underperforming, radiant barrier is treating the symptom. We’ll tell you straight if the money is better spent on insulation first. No pressure, no upcharge.
Attic Cleaning Services
Attic Cleaning Services remove years of dust, debris, pest droppings, and old degraded insulation so a fresh install starts from a clean surface. You need it when you can smell something faintly musty in the upstairs hallway, when there’s visible rodent sign in the attic, or when the old insulation has been contaminated by roof leaks. In Henderson, dust infiltration through attic vents is heavier during the spring wind events that roll off the mountains, and that dust settles straight into loose fill. We bag and haul out everything, treat the space, and can follow with new insulation or spray foam in the same visit. Attic cleaning typically runs $600 to $1,600 depending on square footage and how much contaminated material comes out, with the exact number in writing before we start.
What Gets Removed
Everything: old insulation, dust, construction debris, and rodent waste. We work in HEPA-filtered equipment and bag from the attic hatch so nothing travels through your house. Your hallway gets a drop cloth before we open the hatch.

When Cleaning Comes First
If old insulation has been soaked by a roof leak or fouled by animals, no new insulation should go on top of it. Cleaning first protects the new material and the air your family breathes. We’ll tell you honestly if a clean is needed.

Attic Mold Removal
Attic Mold Removal is the process of treating active mold growth on attic framing and sheathing, correcting the moisture source that allowed it, and verifying the air is clean before anyone goes back to work up there. Henderson’s dry climate doesn’t make attics immune to mold; a single roof leak, a bathroom fan ducted into the attic by mistake, or a winter condensation event is enough to start colonies on the underside of the roof deck. We inspect, contain the work area, treat the affected surfaces with an approved antimicrobial, and then correct the ventilation or duct issue that caused it. Attic mold removal in Henderson typically runs $1,200 to $3,500 depending on the affected area and whether ventilation correction is included, with the written price in hand before any treatment starts.
Finding the Moisture Source
Killing the mold without finding the water is a waste of money. Bath fans venting to the attic and small roof leaks are the two culprits we find most often in Henderson homes. We trace the source before we treat a single surface.
Containment and Verification
We seal off the attic opening with plastic sheeting and run negative air through a HEPA filter while we work. When the treatment is done, we re-inspect the affected framing before we close the job. No “probably fine” reporting.
Attic Insulation Removal
Attic Insulation Removal is the full extraction of old insulation, contaminated or waterlogged material, so new insulation can go in clean or so a spray foam job can bond directly to the framing. You need it when the old material is soaked, fouled by animals, has been eaten away by insects, or when you’re switching to spray foam and the old batt and loose fill would interfere with adhesion. We run vacuum extraction with HEPA filtration, haul the material out in sealed bags, and dispose of it per local requirements. Removal typically costs $900 to $2,000 for an average Henderson attic, quoted in writing before we begin. Most removal jobs happen the same visit as the new install.
When Removal Is Required
Spray foam installs need bare framing; old insulation can’t stay. Contaminated insulation also can’t be top-dressed. If you’re not sure, we’ll inspect and give you both options side by side.
Keeping Your Home Clean
Extraction is the dirtiest part of attic work and the easiest to do badly. We seal the hatch, run the vacuum through a window, and lay drop cloths on the hallway floor before the crew steps inside. Your house is cleaner when we leave than when we arrived.
Brands We Service
We install and service Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demelec, and GreenFiber products, and we know where each one performs best. Owens Corning’s fiberglass batts and loose fill are the workhorses for most Henderson homes, and we know how their lines behave at depth. Johns Manville and Knauf blow-in products handle heat well, and we match their densities to your attic’s target R-value. Rockwool’s mineral wool shines where fire resistance matters and the framing runs tight.
CertainTeed’s radiant barrier products are the ones we reach for when reflection is the job, and Icynene and Demelec cover spray foam, with open-cell for interior walls and closed-cell where a vapor barrier matters. GreenFiber’s cellulose settles predictably into loose-fill jobs. Whether you have Owens Corning, Johns Manville, or any other make in your attic right now, we can help. Our specification comes from what the house needs, not what happens to be sitting in the van.
Signs You Need a Pro Right Now
- Upstairs rooms that won’t cool below 80°F: If the thermostat is set to 74 and the kids’ bedrooms read 82, your attic insulation isn’t holding the line. This is the most common call we get in Henderson from June through September.
- Attic temperatures above 140°F: A properly insulated and vented attic stays well below that. If you stick a thermometer at the hatch on a July afternoon and it reads 155°F, heat is coming through too easily.
- Visible sunken insulation: Walk the attic with a flashlight and look at the depth. If the loose fill is only a few inches deep, or you can see bare ceiling joists, you’re below where a Henderson home should be. A top-up is likely cheaper than replacing your AC.
- Damp, musty smell in the upstairs hallway: That smell is moisture, and moisture in an attic usually means a leak, a vented bath fan, or a ventilation problem. Left alone, it turns into mold on the framing.
- Ice-cold spots in winter or warm spots in summer: If one room stays hotter than the rest, the insulation over it is likely missing, compressed, or displaced. We find the drywall-on-joist gaps in five minutes.
Our Process, Step by Step
- 1
Call and schedule. A live person answers when you call (833) 734-5217, no voicemail, no callback window. We book a time that fits your day and confirm the arrival window in writing.
- 2
In-home inspection. We walk the attic with you by phone or in person, photograph the insulation, check venting, and measure current R-value and depth. We use a thermal imaging camera when the diagnosis is unclear.
- 3
Written price. You get a written price before any work starts: material, R-value target, depth, and what’s included, in plain language. No door-step changes.
- 4
Install day. Background-checked, uniformed technicians arrive in the committed window, drop-cloth the hatch, and work clean. We run HEPA filtration on removal jobs and bag all old material.
- 5
The Kingswell Guarantee in writing. Every job is covered by The Kingswell Guarantee: written price, committed window, clean site, and a written guarantee on the work. If any of it fails within 365 days, we come back and make it right at no charge.
How Much Does Attic Insulation Cost in Henderson?
A typical blown-in attic insulation job in Henderson runs $1,500 to $3,500 depending on attic square footage, current depth, and the R-value you need to hit. Spray foam runs higher, typically $2,800 to $5,500 for an average single-family attic, because the material and labor cost more per square foot. Radiant barrier adds $1,000 to $2,400. Attic insulation removal adds $900 to $2,000 on top of the install. Ventilation correction adds $400 to $1,200. Cleaning runs $600 to $1,600, and mold removal $1,200 to $3,500 depending on affected area.
What drives the price up: attic size above 1,800 square feet, low-pitch roofs that slow the crew, existing insulation that has to come out, and ventilation correction. What brings it down: a clean attic with existing vents already working, a straightforward blown-in top-up, and no moisture issues.
How to avoid overpaying: ask for the R-value in the written quote, confirm whether removal and disposal are included, and insist on a written price before any work starts. Free estimates include measurement, R-value assessment, ventilation check, and a moisture inspection. We’ll point out what actually matters for your house and skip the upsells that pad the bill.
Our Service Area Near Henderson
We serve homeowners across the Las Vegas Valley, with same-day and next-day availability for most requests around our service area. Beyond Henderson, we work in Whitney just north, Paradise to the west, and Winchester, Enterprise, Spring Valley, Sunrise Manor, Summerlin, North Las Vegas, Las Vegas, Boulder City, and Sandy Valley. If you’re on the far side of the valley, expect an arrival window that fits the drive, and we’ll give you the honest estimate before you commit to an appointment.
Serving Henderson, NV – Our Local Coverage Area
We serve Henderson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Attic Insulation in Henderson
Attic Insulation is the layer of material on your attic floor or roof deck that slows heat transfer between your house and the outside. In Henderson’s desert climate it matters most in summer, when a well-insulated attic can cut your cooling bill by 15 to 30 percent versus an under-insulated one. The right material and depth hold the cool air your AC is paying for. If you’re unsure where your attic stands, we’ll take a look at no charge.
Most blown-in attic insulation jobs in Henderson are finished in one day, usually four to six hours for an average single-family home. Spray foam takes longer, often a full day or two depending on square footage. Removal jobs add two to four hours on top. We’ll give you a firm window when we write the price, and we hold to it. Call (833) 734-5217 to book.
Blown-in attic insulation in Henderson typically runs $1,500 to $3,500 depending on square footage and target R-value. Spray foam runs $2,800 to $5,500. Radiant barrier adds $1,000 to $2,400, and removal adds $900 to $2,000. Call (833) 734-5217 for an exact quote. Estimates are free and there’s no obligation.
Yes, we install and service Owens Corning insulation among the eight brands we work with, including Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demelec, and GreenFiber. We’ll match the right material to your attic’s venting, framing, and target R-value. Call for an honest recommendation, and we’ll tell you if a cheaper product does the job. (833) 734-5217 reaches a live person, any hour.
Yes, requests placed before noon are often handled the same day across Henderson. Attic mold, water intrusion, and animal contamination we treat as priority work, because those get worse fast. Call (833) 734-5217 and a live person will confirm the window with you. No voicemail, no call-back queue.
Every job is covered by the 365-Day Done Right Promise, included in writing at no additional charge. If a repair or installation fails within 365 days, we come back and fix it. The written guarantee comes with a free second visit if the work fails, and the same terms apply whether you’re in Henderson or anywhere else in our service area. Call (833) 734-5217 with any warranty question.
Clear the attic hatch access and move any vehicles blocking the driveway. Close the doors to the rooms under the hatch, and if you have pets, put them in a room away from the work area. That’s usually all we need. We handle the drop cloths, bagging, and cleanup, and we leave the site cleaner than we found it. Call (833) 734-5217 if you have questions before the crew arrives.
Schedule Your Attic Insulation Service in Henderson Today
If your upstairs rooms won’t stay cool or your attic is showing signs of trouble, don’t wait for the July heat to decide for you. Call (833) 734-5217 and a live person will answer, day or night, to book a free estimate. You’ll get a written price before any work starts, a committed arrival window, and the 365-Day Done Right Promise behind every job. No obligation, no surprise charges, just an honest answer.
Written by the team at Woolsey Attic Insulation Henderson.